DSN_KLR650
-
Judson D. Jones
- Posts: 1037
- Joined: Sun Sep 29, 2002 11:52 am
Post
by Judson D. Jones » Sun Jan 04, 2004 9:37 pm
--- In
DSN_klr650@yahoogroups.com, "artizun"
wrote:
> I wear a Shoei full face helmet. But it I'm traveling 90% of my
time
> off road this summer is a dirt oriented helmet with goggles
better?
> How are the off road helmets on the road? In the rain? In the
cold?
> In the heat? Noisy? Thanks Pam
An offroad helmet can be tolerable (but not great) on the road
with a nose-piece on the goggles, earplugs, and a balaclava for
cool weather. The nose-piece is the only thing that will make rain
riding comfortable.
-
thad_carey
- Posts: 264
- Joined: Sun Sep 21, 2003 10:53 am
Post
by thad_carey » Sun Jan 04, 2004 10:55 pm
--- In
DSN_klr650@yahoogroups.com, "artizun" wrote:
> I wear a Shoei full face helmet. But it I'm traveling 90% of my
time
> off road this summer is a dirt oriented helmet with goggles better?
> How are the off road helmets on the road? In the rain? In the cold?
> In the heat? Noisy? Thanks Pam
I find Judson's comments about the goggle extender/nose piece to
be very true for any type of riding. In fact I suggest if/when you
buy a helmet, that you buy the goggles and nose piece at the same
time to insure that they fit well and comfortably for you. For
example, I have a fairly new Bell Moto 6 with Oakley OTG (over the
glasses) goggles with an accessory nose piece. No you don't have to
wear glasses to use these goggles--many off roaders use them because
they are more comfortable and fog less. My goggles and nose piece
almost have a custom fit at the chin/jaw guard of the helmet. There
is still enough ventilation for hot days but not the direct blast of
either hot or cold air. Our Texas .50 cal grasshoppers also can't
bean you under the goggles. This nose piece also keeps your nose
from getting sunburned. I also like wearing some nice Oakley shades
under these goggles, and with a clear lens, when it gets dark I just
take the shades off. This can be a big investment, so really try
some helmet/goggle combos out so you get a good satisfying fit. This
can be a major pain if the two don't mesh well. On the KLR I wearing
nothing but an off road helmet. Oh, wait a minute, don't take that
wrong...I do wear clothes too.
Thad Carey
A15 (GI Joe in Barbie drag)
-
Chris
- Posts: 1250
- Joined: Wed Jul 31, 2013 11:57 am
Post
by Chris » Sun Jan 04, 2004 11:43 pm
On Mon, Jan 05, 2004 at 02:41:36AM -0000, artizun wrote:
> I wear a Shoei full face helmet. But it I'm traveling 90% of my time
> off road this summer is a dirt oriented helmet with goggles better?
> How are the off road helmets on the road? In the rain? In the cold?
> In the heat? Noisy? Thanks Pam
I have an RF900 Shoei, I almost cooked myself wearing it on trails
last summer. This year I'm also going to own an MX helmet and
goggles. Also, the amount you sweat offroading, if your Shoei doesn't
have a removeable liner, I suggest storing it in the garage

.
MX helmets are all about ventilation. They are noisy, wet and cold in
the cold.
If you aren't concerned with roost protection the visor and chinpiece
gives you, at least look at a flip-front helmet like the Nolan so you
have easy access to fresh air.
--
___ ______ _____ __ ________ ___
/ _ |< < / == / ___/__ / /_ /_ __/ / __ ____ _ ___ /__ \
/ __ |/ // / ****/ (_ / _ \/ __/ / / / _ \/ // / ' \/ _ \ /__/
/_/ |_/_//_/ == \___/\___/\__/ /_/ /_//_/\_,_/_/_/_/ .__/ (_)
8600 miles*Russel Lines*Supertrapp Race* /_/
http://www.panix.com/~cesser/mybike/
-
ron criswell
- Posts: 1118
- Joined: Fri Apr 07, 2000 5:09 pm
Post
by ron criswell » Thu Nov 01, 2012 5:38 am
Sent from my iPad
I picked up a great dual sport helmet yesterday at Cycle Gear. It is a Bilt and similar to my Arai but with one added feature...two visors. A clear one on the outside and a flip down tinted one on the inside (button controlled). Plus it has the sun visor on top like the Arai. Normally it is a $200 helmet but it was on sale for $100. The Arai shell is probably stronger but it cost me $600. Christmas came early.
Criswell
-
achesley43@ymail.com
- Posts: 262
- Joined: Sun Mar 11, 2012 8:16 pm
Post
by achesley43@ymail.com » Thu Nov 01, 2012 6:54 am
I was wondering about that hat. How much wind effect do you get at speed on the visor? I had to use the old electrical tape thing on my visor yesterday riding into the afternoon sun.
Andy in Jennings. KLR and Bandit
--- In
DSN_KLR650@yahoogroups.com, Ron Criswell wrote:
>
>
>
> Sent from my iPad
>
> I picked up a great dual sport helmet yesterday at Cycle Gear. It is a Bilt and similar to my Arai but with one added feature...two visors. A clear one on the outside and a flip down tinted one on the inside (button controlled). Plus it has the sun visor on top like the Arai. Normally it is a $200 helmet but it was on sale for $100. The Arai shell is probably stronger but it cost me $600. Christmas came early.
>
> Criswell
>
-
ron criswell
- Posts: 1118
- Joined: Fri Apr 07, 2000 5:09 pm
Post
by ron criswell » Thu Nov 01, 2012 7:15 am
I will let you know but haven't taken a test ride yet. Will do today. The outside visor seems to seal very well. I have done the electrician tape thing myself but really like the motocross type visor on my Arai. It is vented very well and I ride at speeds of 80 mph or so with no head rip off tendencies. The Bilt seems similar in this respect. Afternoon sun or early morning sun riding into can be really dangerous if you are blinded by the sun. Speaking from experience on that one.
Criswell
Sent from my iPad
On Nov 1, 2012, at 6:54 AM, "achesley43@..." wrote:
>
> I was wondering about that hat. How much wind effect do you get at speed on the visor? I had to use the old electrical tape thing on my visor yesterday riding into the afternoon sun.
>
> Andy in Jennings. KLR and Bandit
> --- In
DSN_KLR650@yahoogroups.com, Ron Criswell wrote:
> >
> >
> >
> > Sent from my iPad
> >
> > I picked up a great dual sport helmet yesterday at Cycle Gear. It is a Bilt and similar to my Arai but with one added feature...two visors. A clear one on the outside and a flip down tinted one on the inside (button controlled). Plus it has the sun visor on top like the Arai. Normally it is a $200 helmet but it was on sale for $100. The Arai shell is probably stronger but it cost me $600. Christmas came early.
> >
> > Criswell
> >
>
>
[Non-text portions of this message have been removed]
-
SniperOne
- Posts: 96
- Joined: Wed May 09, 2012 11:27 am
Post
by SniperOne » Thu Nov 01, 2012 8:57 am
I looked at the Bilt DS helmet when they first arrived at the local Cycle Gear. It looked interesting until I noticed Bilt had not designed a moulded-in or attached grasping point at the bottom edge of the face shield to open and close it with.
I asked the sales person if there was a hidden lever for opening and closing. He looked and didn't find one either. So, not being a fan of planting a dirty glove across a dusty shield to slide it open/closed, I put the helmet back on the shelf.
Randy
Sent from my Verizon Wireless Phone
-----Original Message-----
From: Ron Criswell
Sent: Thursday, November 01, 2012 6:15 AM
To: achesley43@...
Cc:
DSN_KLR650@yahoogroups.com DSN_KLR650@yahoogroups.com>
Subject: Re: [DSN_KLR650] Re: Helmet
I will let you know but haven't taken a test ride yet. Will do today. The outside visor seems to seal very well. I have done the electrician tape thing myself but really like the motocross type visor on my Arai. It is vented very well and I ride at speeds of 80 mph or so with no head rip off tendencies. The Bilt seems similar in this respect. Afternoon sun or early morning sun riding into can be really dangerous if you are blinded by the sun. Speaking from experience on that one.
Criswell
Sent from my iPad
On Nov 1, 2012, at 6:54 AM, "achesley43@..." wrote:
>
> I was wondering about that hat. How much wind effect do you get at speed on the visor? I had to use the old electrical tape thing on my visor yesterday riding into the afternoon sun.
>
> Andy in Jennings. KLR and Bandit
> --- In
DSN_KLR650@yahoogroups.com, Ron Criswell wrote:
> >
> >
> >
> > Sent from my iPad
> >
> > I picked up a great dual sport helmet yesterday at Cycle Gear. It is a Bilt and similar to my Arai but with one added feature...two visors. A clear one on the outside and a flip down tinted one on the inside (button controlled). Plus it has the sun visor on top like the Arai. Normally it is a $200 helmet but it was on sale for $100. The Arai shell is probably
[The entire original message is not included]
[Non-text portions of this message have been removed]
-
mark ward
- Posts: 1027
- Joined: Fri Jan 15, 2010 11:18 am
Post
by mark ward » Thu Nov 01, 2012 9:37 am
No lip.
Thats a speacial "feature".
It is designed for left OR right handed riders.
Enclosed in the box, you would have found Two.................................
3inch long peice's of 'DUCT TAPE", to fold over and applie to the edge of the lid.
1 on the right or left for your preferance, OR Both sides if you are ambidextrous.
OR Attach them together, and applie right in the center, for a long tab, for use with gloves.
I know crazy huh?...they should have just sent a 6 inch peice.
Sorry, I want to RIDE, But, it's 38dig and RAINY out in West Michigan, and when I looked at Mountain city Tenessee it wasn't any warmer.
--- On Thu, 11/1/12, SniperOne wrote:
From: SniperOne
Subject: RE: [DSN_KLR650] Re: Helmet
To:
Cc: "KLR List" DSN_KLR650@yahoogroups.com>
Date: Thursday, November 1, 2012, 1:57 PM
I looked at the Bilt DS helmet when they first arrived at the local Cycle Gear. It looked interesting until I noticed Bilt had not designed a moulded-in or attached grasping point at the bottom edge of the face shield to open and close it with.
I asked the sales person if there was a hidden lever for opening and closing. He looked and didn't find one either. So, not being a fan of planting a dirty glove across a dusty shield to slide it open/closed, I put the helmet back on the shelf.
Randy
Sent from my Verizon Wireless Phone
-----Original Message-----
From: Ron Criswell
Sent: Thursday, November 01, 2012 6:15 AM
To: achesley43@...
Cc:
DSN_KLR650@yahoogroups.com DSN_KLR650@yahoogroups.com>
Subject: Re: [DSN_KLR650] Re: Helmet
I will let you know but haven't taken a test ride yet. Will do today. The outside visor seems to seal very well. I have done the electrician tape thing myself but really like the motocross type visor on my Arai. It is vented very well and I ride at speeds of 80 mph or so with no head rip off tendencies. The Bilt seems similar in this respect. Afternoon sun or early morning sun riding into can be really dangerous if you are blinded by the sun. Speaking from experience on that one.
Criswell
Sent from my iPad
On Nov 1, 2012, at 6:54 AM, "achesley43@..." wrote:
>
> I was wondering about that hat. How much wind effect do you get at speed on the visor? I had to use the old electrical tape thing on my visor yesterday riding into the afternoon sun.
>
> Andy in Jennings. KLR and Bandit
> --- In
DSN_KLR650@yahoogroups.com, Ron Criswell wrote:
> >
> >
> >
> > Sent from my iPad
> >
> > I picked up a great dual sport helmet yesterday at Cycle Gear. It is a Bilt and similar to my Arai but with one added feature...two visors. A clear one on the outside and a flip down tinted one on the inside (button controlled). Plus it has the sun visor on top like the Arai. Normally it is a $200 helmet but it was on sale for $100. The Arai shell is probably
[The entire original message is not included]
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
-
RobertWichert
- Posts: 697
- Joined: Sun Jan 10, 2010 11:32 am
Post
by RobertWichert » Thu Nov 01, 2012 10:03 am
My Arai came with a little lifting nub on the left side that also serves
to crack the shield open for foggy conditions, or something. It broke
off. The shields are so expensive, that now I just dig into it on the
corner with my glove. It's working so far!
Robert Wichert P.Eng. LEED AP BD&C
+1 916 966 9060
FAX +1 916 966 9068
===============================================
On 11/1/2012 7:37 AM, mark ward wrote:
>
> No lip.
>
> Thats a speacial "feature".
> It is designed for left OR right handed riders.
>
> Enclosed in the box, you would have found
> Two.................................
> 3inch long peice's of 'DUCT TAPE", to fold over and applie to the edge
> of the lid.
>
> 1 on the right or left for your preferance, OR Both sides if you are
> ambidextrous.
>
> OR Attach them together, and applie right in the center, for a long
> tab, for use with gloves.
>
> I know crazy huh?...they should have just sent a 6 inch peice.
>
> Sorry, I want to RIDE, But, it's 38dig and RAINY out in West Michigan,
> and when I looked at Mountain city Tenessee it wasn't any warmer.
>
> --- On Thu, 11/1/12, SniperOne > wrote:
>
> From: SniperOne >
> Subject: RE: [DSN_KLR650] Re: Helmet
> To:
> Cc: "KLR List" DSN_KLR650@yahoogroups.com
> >
> Date: Thursday, November 1, 2012, 1:57 PM
>
>
>
> I looked at the Bilt DS helmet when they first arrived at the local
> Cycle Gear. It looked interesting until I noticed Bilt had not
> designed a moulded-in or attached grasping point at the bottom edge of
> the face shield to open and close it with.
>
> I asked the sales person if there was a hidden lever for opening and
> closing. He looked and didn't find one either. So, not being a fan of
> planting a dirty glove across a dusty shield to slide it open/closed,
> I put the helmet back on the shelf.
>
> Randy
>
> Sent from my Verizon Wireless Phone
>
> -----Original Message-----
> From: Ron Criswell >
> Sent: Thursday, November 01, 2012 6:15 AM
> To: achesley43@...
> >
> Cc:
DSN_KLR650@yahoogroups.com
> DSN_KLR650@yahoogroups.com >
> Subject: Re: [DSN_KLR650] Re: Helmet
>
> I will let you know but haven't taken a test ride yet. Will do today.
> The outside visor seems to seal very well. I have done the electrician
> tape thing myself but really like the motocross type visor on my Arai.
> It is vented very well and I ride at speeds of 80 mph or so with no
> head rip off tendencies. The Bilt seems similar in this respect.
> Afternoon sun or early morning sun riding into can be really dangerous
> if you are blinded by the sun. Speaking from experience on that one.
>
> Criswell
>
> Sent from my iPad
>
> On Nov 1, 2012, at 6:54 AM, "achesley43@...
> " > wrote:
>
> >
> > I was wondering about that hat. How much wind effect do you get at
> speed on the visor? I had to use the old electrical tape thing on my
> visor yesterday riding into the afternoon sun.
> >
> > Andy in Jennings. KLR and Bandit
> > --- In
DSN_KLR650@yahoogroups.com
> , Ron Criswell
> wrote:
> > >
> > >
> > >
> > > Sent from my iPad
> > >
> > > I picked up a great dual sport helmet yesterday at Cycle Gear. It
> is a Bilt and similar to my Arai but with one added feature...two
> visors. A clear one on the outside and a flip down tinted one on the
> inside (button controlled). Plus it has the sun visor on top like the
> Arai. Normally it is a $200 helmet but it was on sale for $100. The
> Arai shell is probably
>
> [The entire original message is not included]
>
> [Non-text portions of this message have been removed]
>
> [Non-text portions of this message have been removed]
>
>
[Non-text portions of this message have been removed]
-
Bill Kinnison
- Posts: 24
- Joined: Thu Jan 05, 2012 12:30 pm
Post
by Bill Kinnison » Thu Nov 01, 2012 10:50 am
I brought that up on the ADV site. A few of the guys who bought the helmet
already have said it wasn't really an issue, even with gloves on.
I like the dual shield idea. But haven't been able to justify replacing my
less than 1 yr old FX39 yet. We'll see. Hope to get over to CG sometime
just to check it out.
-
Bill
On Thu, Nov 1, 2012 at 8:03 AM, RobertWichert wrote:
> **
>
>
> My Arai came with a little lifting nub on the left side that also serves
> to crack the shield open for foggy conditions, or something. It broke
> off. The shields are so expensive, that now I just dig into it on the
> corner with my glove. It's working so far!
>
> Robert Wichert P.Eng. LEED AP BD&C
> +1 916 966 9060
> FAX +1 916 966 9068
>
> ===============================================
>
>
> On 11/1/2012 7:37 AM, mark ward wrote:
> >
> > No lip.
> >
> > Thats a speacial "feature".
> > It is designed for left OR right handed riders.
> >
> > Enclosed in the box, you would have found
> > Two.................................
> > 3inch long peice's of 'DUCT TAPE", to fold over and applie to the edge
> > of the lid.
> >
> > 1 on the right or left for your preferance, OR Both sides if you are
> > ambidextrous.
> >
> > OR Attach them together, and applie right in the center, for a long
> > tab, for use with gloves.
> >
> > I know crazy huh?...they should have just sent a 6 inch peice.
> >
> > Sorry, I want to RIDE, But, it's 38dig and RAINY out in West Michigan,
> > and when I looked at Mountain city Tenessee it wasn't any warmer.
> >
> > --- On Thu, 11/1/12, SniperOne > > wrote:
> >
> > From: SniperOne >>
>
> > Subject: RE: [DSN_KLR650] Re: Helmet
> > To:
> > Cc: "KLR List" DSN_KLR650@yahoogroups.com
> > >
>
> > Date: Thursday, November 1, 2012, 1:57 PM
> >
> >
> >
> > I looked at the Bilt DS helmet when they first arrived at the local
> > Cycle Gear. It looked interesting until I noticed Bilt had not
> > designed a moulded-in or attached grasping point at the bottom edge of
> > the face shield to open and close it with.
> >
> > I asked the sales person if there was a hidden lever for opening and
> > closing. He looked and didn't find one either. So, not being a fan of
> > planting a dirty glove across a dusty shield to slide it open/closed,
> > I put the helmet back on the shelf.
> >
> > Randy
> >
> > Sent from my Verizon Wireless Phone
> >
> > -----Original Message-----
> > From: Ron Criswell > >
> > Sent: Thursday, November 01, 2012 6:15 AM
> > To: achesley43@...
> > >
> > Cc:
DSN_KLR650@yahoogroups.com
> > DSN_KLR650@yahoogroups.com >
> > Subject: Re: [DSN_KLR650] Re: Helmet
> >
> > I will let you know but haven't taken a test ride yet. Will do today.
> > The outside visor seems to seal very well. I have done the electrician
> > tape thing myself but really like the motocross type visor on my Arai.
> > It is vented very well and I ride at speeds of 80 mph or so with no
> > head rip off tendencies. The Bilt seems similar in this respect.
> > Afternoon sun or early morning sun riding into can be really dangerous
> > if you are blinded by the sun. Speaking from experience on that one.
> >
> > Criswell
> >
> > Sent from my iPad
> >
> > On Nov 1, 2012, at 6:54 AM, "achesley43@...
> > " > > wrote:
> >
> > >
> > > I was wondering about that hat. How much wind effect do you get at
> > speed on the visor? I had to use the old electrical tape thing on my
> > visor yesterday riding into the afternoon sun.
> > >
> > > Andy in Jennings. KLR and Bandit
> > > --- In
DSN_KLR650@yahoogroups.com
> > , Ron Criswell
> > wrote:
> > > >
> > > >
> > > >
> > > > Sent from my iPad
> > > >
> > > > I picked up a great dual sport helmet yesterday at Cycle Gear. It
> > is a Bilt and similar to my Arai but with one added feature...two
> > visors. A clear one on the outside and a flip down tinted one on the
> > inside (button controlled). Plus it has the sun visor on top like the
> > Arai. Normally it is a $200 helmet but it was on sale for $100. The
> > Arai shell is probably
> >
> > [The entire original message is not included]
> >
> > [Non-text portions of this message have been removed]
> >
> > [Non-text portions of this message have been removed]
> >
> >
>
> [Non-text portions of this message have been removed]
>
>
>
[Non-text portions of this message have been removed]
Users browsing this forum: No registered users and 28 guests