spotted 04 klr north carolina
-
- Posts: 63
- Joined: Fri May 28, 2004 7:51 am
pics of broken crankcase
hi. A couple weeks ago, I broke the threaded part of the oil drain hole on my crankcase.
My mechanic told me, it can't be welded, but we can try to put on a rubber expanding plug & with every oil change, replace it with a new one. Or a sealed steel sheet can be put on the case. (Otherwise, I will have to buy new crankcases.)
This time I'm sending photos, so feel free to offer any other suggestions
---------------------------------
Do you Yahoo!?
Friends. Fun. Try the all-new Yahoo! Messenger
[Non-text portions of this message have been removed]
-
- Posts: 549
- Joined: Fri Apr 07, 2000 3:12 pm
pics of broken crankcase
Good morning. I installed one in my Peugeot and it lasted for years. The
plug I used was rubber one with a removable bolt insert so that you could
change the oil. I got it the local auto supply store.
George
Escondido, Ca
----- Original Message ----- From: "sergio de oliveira" To: DSN_klr650@yahoogroups.com> Sent: Thursday, June 10, 2004 8:34 AM Subject: [DSN_klr650] pics of broken crankcase > hi. A couple weeks ago, I broke the threaded part of the oil drain hole on my crankcase. > My mechanic told me, it can't be welded, but we can try to put on a rubber expanding plug & with every oil change, replace it with a new one. Or a sealed steel sheet can be put on the case. (Otherwise, I will have to buy new crankcases.) > This time I'm sending photos, so feel free to offer any other suggestions > > > > > > --------------------------------- > Do you Yahoo!? > Friends. Fun. Try the all-new Yahoo! Messenger > > [Non-text portions of this message have been removed] > > > > List sponsored by Dual Sport News at www.dualsportnews.com. List FAQ courtesy of Chris Krok at: www.bigcee.com/klr650faq.html > Unsubscribe by sending a blank message to: > DSN_klr650-unsubscribe@yahoogroups.com . > > > Yahoo! Groups Links > > > > >
-
- Posts: 717
- Joined: Wed Jun 20, 2001 6:17 am
pics of broken crankcase
Why can't it be welded? I've seen parts of the KLR cases that have
been welded. If you have to split the cases to do it, so what!
What's cheaper, a new set of cases or the time it takes to split and
weld them. If cast iron engine blocks can be welded, why can't a
cast aluminum one be? I'm curious.
millerized
--- In DSN_klr650@yahoogroups.com, sergio de oliveira
wrote:
hole on my crankcase.> hi. A couple weeks ago, I broke the threaded part of the oil drain
rubber expanding plug & with every oil change, replace it with a new one. Or a sealed steel sheet can be put on the case. (Otherwise, I will have to buy new crankcases.)> My mechanic told me, it can't be welded, but we can try to put on a
suggestions> This time I'm sending photos, so feel free to offer any other
> > > > > > --------------------------------- > Do you Yahoo!? > Friends. Fun. Try the all-new Yahoo! Messenger > > [Non-text portions of this message have been removed]
-
- Posts: 1442
- Joined: Tue Jan 21, 2003 7:59 pm
pics of broken crankcase
In a message dated 2004-06-10 8:39:31 AM Pacific Daylight Time,
sergio750102000@... writes:
Sergio, Did you post the pictures? I went looking but didn't see any. As long as the hole is still more or less round, an expanding rubber plug can be used. For year now they have become the norm for fixing stripped out oil pan drain plugs on cars. Ran one on a F150 for four years without any problems. Pat G'ville, Nv [Non-text portions of this message have been removed]> > hi. A couple weeks ago, I broke the threaded part of the oil drain hole on > my crankcase. > My mechanic told me, it can't be welded, but we can try to put on a rubber > expanding plug &with every oil change, replace it with a new one. Or a sealed > steel sheet can be put on the case. (Otherwise, I will have to buy new > crankcases.) > This time I'm sending photos, so feel free to offer any other suggestions > >
-
- Posts: 122
- Joined: Wed Feb 25, 2004 8:40 am
pics of broken crankcase
I dont understand why it cant be welded either. I knocked a hole in
in the left side case of my TTR 250 a couple of months ago and had
it welded back. Better than new now. Take it to a welding shop and
a good welder will know what to do. It takes a ver good welder and
one that knows aluminum to get it done right but they are out
their. The guy that did mine said it was more like brazing than
welding.
--- In DSN_klr650@yahoogroups.com, "James L. Miller Jr."
wrote:
have> Why can't it be welded? I've seen parts of the KLR cases that
and> been welded. If you have to split the cases to do it, so what! > What's cheaper, a new set of cases or the time it takes to split
drain> weld them. If cast iron engine blocks can be welded, why can't a > cast aluminum one be? I'm curious. > > millerized > > > --- In DSN_klr650@yahoogroups.com, sergio de oliveira > wrote: > > hi. A couple weeks ago, I broke the threaded part of the oil
on a> hole on my crankcase. > > My mechanic told me, it can't be welded, but we can try to put
new> rubber expanding plug & with every oil change, replace it with a
I> one. Or a sealed steel sheet can be put on the case. (Otherwise,
> will have to buy new crankcases.) > > This time I'm sending photos, so feel free to offer any other > suggestions > > > > > > > > > > > > --------------------------------- > > Do you Yahoo!? > > Friends. Fun. Try the all-new Yahoo! Messenger > > > > [Non-text portions of this message have been removed]
-
- Posts: 1037
- Joined: Sun Sep 29, 2002 11:52 am
pics of broken crankcase
--- In DSN_klr650@yahoogroups.com, "George Basinet" wrote:
Lucky for you you are in California. Peugeots don't last for years in Minnesota.> Good morning. I installed one in my Peugeot and it lasted for years.
-
- Posts: 1442
- Joined: Tue Jan 21, 2003 7:59 pm
pics of broken crankcase
In a message dated 2004-06-11 11:09:11 AM Pacific Daylight Time,
dirtrooster2003@... writes:
Sergio sent me copies of the damage photos and I've posted them in the pictures undre a folder named Sergio's Drain Plug - http://photos.groups.yahoo.com/group/dsn_klr650/lst?&.dir=/Sergio%27s+DrainPlug&.src=gr&.view=t& .url=http%3a//us.f1.yahoofs.com/groups/g_488385/Sergio%2527s%2bDrainPlug/plug1.jpg%3fbcDoFyvB ny9TDj8k&.cx=150&.cy=112&.type=u It is bad, but it doesn't look terminal. I can see a lot of weldors running away from something like this, but it doesn't look any worse than the crankshaft bearing race I popped out. Perhaps I was lucky in having a friend of the family who ran the shop department at a California JC, but he was able to weld things up and then machined in a new bearing race. Such a repair can be done, but you might need to be looking for those weldors that would be called artists by their peers. I've got a buddy who is a master at keeping rat bikes on the road. I showed him the pics and he gave me his stock answer, JB Weld will fix it. Pat G'ville, Nv [Non-text portions of this message have been removed]> > I dont understand why it cant be welded either. I knocked a hole in > in the left side case of my TTR 250 a couple of months ago and had > it welded back. Better than new now. Take it to a welding shop and > a good welder will know what to do. It takes a ver good welder and > one that knows aluminum to get it done right but they are out > their. The guy that did mine said it was more like brazing than > welding. > >
-
- Posts: 1442
- Joined: Tue Jan 21, 2003 7:59 pm
pics of broken crankcase
Sorry about that, the empty post was to contain this email I got from
biggranger@... - I believe he meant to reply to the group instead of just to me
...
I've fixed worse than this before. It might even be able to be fixed without
splitting the case. I'd clean it up real good, put a long bolt in and fill in
around the bolt (with TIG). Pull the bolt out and drill and tap for a helicoil
by hand and clean the chips away very carefully (helps to coat everything in
grease). Screw in a cap again and file the sealing surface flat. Presto, all
fxed, and about 2 hours of labor.
[Non-text portions of this message have been removed]
-
- Posts: 265
- Joined: Sun May 16, 2004 10:10 pm
pics of broken crankcase
I've fixed worse than this before. It might even be able to be fixed
without splitting the case. I'd clean it up real good, put a long bolt
in and fill in around the bolt (with TIG). Pull the bolt out and drill
and tap for a helicoil by hand and clean the chips away very carefully
(helps to coat everything in grease). Screw in a cap again and file the
sealing surface flat. Presto, all fxed, and about 2 hours of labor.
kdxkawboy@... wrote:
[Non-text portions of this message have been removed]>In a message dated 2004-06-11 11:09:11 AM Pacific Daylight Time, >dirtrooster2003@... writes: > > > >>I dont understand why it cant be welded either. I knocked a hole in >>in the left side case of my TTR 250 a couple of months ago and had >>it welded back. Better than new now. Take it to a welding shop and >>a good welder will know what to do. It takes a ver good welder and >>one that knows aluminum to get it done right but they are out >>their. The guy that did mine said it was more like brazing than >>welding. >> >> >> >> > >Sergio sent me copies of the damage photos and I've posted them in the >pictures undre a folder named Sergio's Drain Plug - >http://photos.groups.yahoo.com/group/dsn_klr650/lst?&.dir=/Sergio%27s+DrainPlug&.src=gr&.view=t& >.url=http%3a//us.f1.yahoofs.com/groups/g_488385/Sergio%2527s%2bDrainPlug/plug1.jpg%3fbcDoFyvB >ny9TDj8k&.cx=150&.cy=112&.type=u > >It is bad, but it doesn't look terminal. I can see a lot of weldors running >away from something like this, but it doesn't look any worse than the >crankshaft bearing race I popped out. Perhaps I was lucky in having a friend of the >family who ran the shop department at a California JC, but he was able to weld >things up and then machined in a new bearing race. Such a repair can be done, >but you might need to be looking for those weldors that would be called artists >by their peers. > >I've got a buddy who is a master at keeping rat bikes on the road. I showed >him the pics and he gave me his stock answer, JB Weld will fix it. > >Pat >G'ville, Nv > > >[Non-text portions of this message have been removed] > > > >List sponsored by Dual Sport News at www.dualsportnews.com. List FAQ courtesy of Chris Krok at: www.bigcee.com/klr650faq.html >Unsubscribe by sending a blank message to: >DSN_klr650-unsubscribe@yahoogroups.com . > > >Yahoo! Groups Links > > > > > > > >
-
- Posts: 122
- Joined: Wed Feb 25, 2004 8:40 am
spotted 04 klr north carolina
Saw an red klr on hwy 74 between laurinburg and rockingham today.
wondering if anybody on group
Who is online
Users browsing this forum: No registered users and 27 guests