2007 parts & part numbers?
-
- Posts: 22
- Joined: Mon Jun 19, 2006 5:00 pm
is a 160 main too rich for open pipe?
I'm talking keihin jet numbers here, not dynojet. Stock needle, stock
pilot, adjusted pilot screw, twinair filter, no snorkel, a few airbox
holes.
My pipe is a straight-through glass packed type, like a Big Gun.
I think the 160 is a bit too rich, as it smokes rich when I squeeze
it. What's everybody else running with an open pipe? My wideband is
sitting here in a box waiting for me to make a TPS and a bung, but
until then, it may be worth leaning it out a little.
-
- Posts: 2759
- Joined: Thu Apr 06, 2000 2:04 pm
is a 160 main too rich for open pipe?
On 3/1/07 3:57 PM, "afmcg1" wrote:
With a de-tweetyfied stock muffler I run a 148 jet and have shimmed the needle with two tiny washers. Curious why you choose a straight through pipe like the Big Guano ? Bogdan [Non-text portions of this message have been removed]> > > > > I'm talking keihin jet numbers here, not dynojet. Stock needle, stock > pilot, adjusted pilot screw, twinair filter, no snorkel, a few airbox > holes. > > My pipe is a straight-through glass packed type, like a Big Gun. > > I think the 160 is a bit too rich, as it smokes rich when I squeeze > it. What's everybody else running with an open pipe? My wideband is > sitting here in a box waiting for me to make a TPS and a bung, but > until then, it may be worth leaning it out a little. > > >
-
- Posts: 712
- Joined: Thu Apr 01, 2004 7:48 am
is a 160 main too rich for open pipe?
Mine has stock exhaust, snorkel removed, inlet air screen removed, No-Toil air filter and 160 main jet. Good mileage, no indications of over rich or lean bog, but have yet to use an exhaust gas analyzer. It runs so well and I'm lazy.
HIH
Norm
[Non-text portions of this message have been removed]
-
- Posts: 60
- Joined: Wed Apr 05, 2006 5:23 pm
is a 160 main too rich for open pipe?
Dynojet DJ150 neddle on 4th clip works well at my elevation 2175 FT.
--- In DSN_KLR650@yahoogroups.com, "afmcg1" wrote: > > I'm talking keihin jet numbers here, not dynojet. Stock needle, stock > pilot, adjusted pilot screw, twinair filter, no snorkel, a few airbox > holes. > > My pipe is a straight-through glass packed type, like a Big Gun. > > I think the 160 is a bit too rich, as it smokes rich when I squeeze > it. What's everybody else running with an open pipe? My wideband is > sitting here in a box waiting for me to make a TPS and a bung, but > until then, it may be worth leaning it out a little. >
-
- Posts: 171
- Joined: Mon Sep 11, 2006 7:07 pm
is a 160 main too rich for open pipe?
Norm, did you notice any difference in power output or drivablility
after those mods?
Ross
--- In DSN_KLR650@yahoogroups.com, "Norm Keller" wrote: > > Mine has stock exhaust, snorkel removed, inlet air screen removed, No- Toil air filter and 160 main jet. Good mileage, no indications of over rich or lean bog, but have yet to use an exhaust gas analyzer. It runs so well and I'm lazy. > > HIH > > Norm > > [Non-text portions of this message have been removed] >
-
- Posts: 22
- Joined: Mon Jun 19, 2006 5:00 pm
is a 160 main too rich for open pipe?
Big Guano. Very clever. My bike came with it. It's louder, but it
gives the bike more go.
I have a mostly stock KLR with a stock pipe that has an opened up
endcap, a KL600 trans and 15/43. The one with the open pipe also has
the KL600 trans and 16/42. Although you'd expect the one geared lower
and closer to stock gearing to be quicker, they are pretty evenly
matched off the line. So the pipe allows it to perform the same off
the line, with gearing that lets me go 80 (on the speedo) just under
5000 RPM.
shimmed the> > > With a de-tweetyfied stock muffler I run a 148 jet and have
through pipe> needle with two tiny washers. Curious why you choose a straight
> like the Big Guano ? > > Bogdan >
-
- Posts: 112
- Joined: Fri Jun 24, 2005 11:19 am
2007 parts & part numbers?
Thanks for the tip - I hadn't gone to both sites before.
So I looked up all the plastics & found it's $385 (!!!!!!) to get new black plastics. I sure don't want it that bad.
Thanks again for your help.
Jeff Layton
Austin, TX A-15
(Going to Big Bend March 23rd & 24th!)
Posted by: "kestrelfal" kestrelfal@... kestrelfal
Thu Mar 1, 2007 2:33 pm (PST)
The part numbers are at kawasaki.com.
---> Motorcyclce/Owner Info/Parts Diagrams/etc.
The prices are at ronayers.com
Fred
--- In DSN_KLR650@yahoogroups.com, "Jeff Layton" wrote: > > Guys - would like to get some prices for a set of 2007 plastics in black. If they're cheap enough, I may want to get some. > > Problem is, the 2007 microfishce's aren't at all the usual places yet. I've been looking on eBay for months & of course found nothing. > > Does anyone here have the ability to look up Kaw part numbers - and maybe pricing - for me? > -------------------------------------------- My mailbox is spam-free with ChoiceMail, the leader in personal and corporate anti-spam solutions. Download your free copy of ChoiceMail from www.digiportal.com [Non-text portions of this message have been removed]
-
- Posts: 2759
- Joined: Thu Apr 06, 2000 2:04 pm
is a 160 main too rich for open pipe?
On 3/1/07 11:54 PM, "afmcg1" wrote:
the KL600 trans and 16/42. So there are 5 known KLR650s with the lower 600 first gears. Kurt Grife s which was the first, mine, the fellow s from Vancouver that hasn t been heard from in a long time and now your two. Welcome to the club. Bogdan [Non-text portions of this message have been removed]> > > > > Big Guano. Very clever. My bike came with it. It's louder, but it > gives the bike more go. > > I have a mostly stock KLR with a stock pipe that has an opened up > endcap, a KL600 trans and 15/43. The one with the open pipe also has
Who is online
Users browsing this forum: No registered users and 23 guests