Wilsons Sandbox

HI Bruce,’

 

Reference FTFU catalog, section 16 – Engine Hardware.  Every nut and bolt is listed.

 

Manifold is held with 4” studs and 8mm nuts.  See catalog Section 16 / Studs

https://www.fromtheframeup.com/uploads/Cat_16_X.pdf

 

 

[b][i]Doug Pelton,[/i][/b] Proprietor

From The Frame Up

480-588-8185

For Fastest Service:  order@fromtheframeup.com

Like us on FACEBOOK!

See us on YouTUBE!

 

www.FromTheFrameUp.com

 

[b]From:[/b] mg-tabc@yahoogroups.com mg-tabc@yahoogroups.com> [b]On Behalf Of [/b]'Bruce Doran-Veevers' bruce@mbssales.ca [mg-tabc] [b]Sent:[/b] Friday, March 30, 2018 5:25 AM [b]To:[/b] mg-tabc@yahoogroups.com [b]Subject:[/b] [mg-tabc] Bolt Size for Air Manifold for MGTC

 

 

I had to do  some engine work over the winter , unfortunately I wasn’t carefully about bagging stuff. Could some one please tell me the length of the four bolts that connect air manifold , I know they are 8 mm , just not sure of the length .

Bruce Doran-Veevers

MBS Sales & Marketing Ltd.

115 Hemlock Dr.

Carleton Place, OnT

K7C 3P2

Cell 613-299-7523

 

 

[img]https://ec.yimg.com/ec?url=https%3A%2F%2Fipmcdn.avast.com%2Fimages%2Ficons%2Ficon-envelope-tick-round-orange-animated-no-repeat-v1.gif&t=1522512048&sig=HNoj5kO7SGfwmcx3ue4Nvw--~D[/img] Virus-free. www.avast.com

Bruce,

 

My error in reading too quick.

 

Info found in same document under bolts.

 

Doug

 

 

[b]From:[/b] Bruce Doran-Veevers bruce@mbssales.ca> [b]Sent:[/b] Friday, March 30, 2018 5:57 AM [b]To:[/b] 'Doug Pelton' doug@fromtheframeup.com> [b]Subject:[/b] RE: [mg-tabc] Bolt Size for Air Manifold for MGTC

 

It is air manifold bolts that I took off , throw them in a bucket of other bolts , instead of putting them in a ziplock bag

 

[b]From:[/b] Doug Pelton doug@fromtheframeup.com> [b]Sent:[/b] Friday, March 30, 2018 8:55 AM [b]To:[/b] 'Bruce Doran-Veevers' bruce@mbssales.ca>; mg-tabc@yahoogroups.com [b]Subject:[/b] RE: [mg-tabc] Bolt Size for Air Manifold for MGTC

 

HI Bruce,’

 

Reference FTFU catalog, section 16 – Engine Hardware.  Every nut and bolt is listed.

 

Manifold is held with 4” studs and 8mm nuts.  See catalog Section 16 / Studs

https://www.fromtheframeup.com/uploads/Cat_16_X.pdf

 

 

[b][i]Doug Pelton,[/i][/b] Proprietor

From The Frame Up

480-588-8185

For Fastest Service:  order@fromtheframeup.com

Like us on FACEBOOK!

See us on YouTUBE!

 

www.FromTheFrameUp.com

 

[b]From:[/b] mg-tabc@yahoogroups.com mg-tabc@yahoogroups.com> [b]On Behalf Of [/b]'Bruce Doran-Veevers' bruce@mbssales.ca [mg-tabc] [b]Sent:[/b] Friday, March 30, 2018 5:25 AM [b]To:[/b] mg-tabc@yahoogroups.com [b]Subject:[/b] [mg-tabc] Bolt Size for Air Manifold for MGTC

 

 

I had to do  some engine work over the winter , unfortunately I wasn’t carefully about bagging stuff. Could some one please tell me the length of the four bolts that connect air manifold , I know they are 8 mm , just not sure of the length .

Bruce Doran-Veevers

MBS Sales & Marketing Ltd.

115 Hemlock Dr.

Carleton Place, OnT

K7C 3P2

Cell 613-299-7523

 

 

 

[img]https://ec.yimg.com/ec?url=https%3A%2F%2Fipmcdn.avast.com%2Fimages%2Ficons%2Ficon-envelope-tick-round-orange-animated-no-repeat-v1.gif&t=1522512048&sig=HNoj5kO7SGfwmcx3ue4Nvw--~D[/img]

Virus-free. www.avast.com

 

hi Bruce & Doug - I think you mean the ones into the inlet air manifold, which are 20mm. Not critical as the holes are not blind. cheers Roger

On Fri, Mar 30, 2018 at 1:24 PM, 'Bruce Doran-Veevers' bruce@mbssales.ca [mg-tabc] mg-tabc-noreply@yahoogroups.com> wrote: [u][/u] I had to do some engine work over the winter , unfortunately I wasn t carefully about bagging stuff. Could some one please tell me the length of the four bolts that connect air manifold , I know they are 8 mm , just not sure of the length . [u][/u][u][/u]

Bruce Doran-Veevers[u][/u][u][/u]

MBS Sales & Marketing Ltd. [u][/u][u][/u]

115 Hemlock Dr.[u][/u][u][/u]

Carleton Place, OnT[u][/u][u][/u]

K7C 3P2[u][/u][u][/u]

Cell 613-299-7523[u][/u][u][/u]

[u][/u] [u][/u]

[u][/u] [u][/u]