Page 1 of 1
MPJG Sump Gasket
Posted: Thu Jan 24, 2002 8:37 am
by Roger Muir
Has anyone experience of using silicone sealant instead of the cork gasket
on the sump of the MPJG engine?
Roger Muir Bromsgrove UK
Re: MPJG Sump Gasket
Posted: Thu Jan 24, 2002 9:32 am
by somexuk
Roger,
not exactly, but tried the cork gasket and found it sqeezed out very
easily and was not happy with that, then made my own thick card
gasket from a good quality eastlight document folder, and fitted this
with a light bead of orange hylomar/hermetite silicon sealant.
No leaks since!
Alan Webster
TA 3239
--- In mg-tabc@y..., Roger Muir wrote:
>
>
> Has anyone experience of using silicone sealant instead of the cork
gasket
> on the sump of the MPJG engine?
>
> Roger Muir Bromsgrove UK
Re: MPJG Sump Gasket
Posted: Thu Jan 24, 2002 11:17 am
by Dean Jensen
The problem I have experienced with that is if you do a really good job in
sealing it, you have one devil of a time taking the sump back off for
whatever reason. It is really stuck together.
Cheers Dean
----- Original Message -----
From: Roger Muir rogermuir@compuserve.com>
To: MG Groups mg-tabc@yahoogroups.com>
Sent: Thursday, January 24, 2002 10:36 AM
Subject: [mg-tabc] MPJG Sump Gasket
>
>
> Has anyone experience of using silicone sealant instead of the cork gasket
> on the sump of the MPJG engine?
>
> Roger Muir Bromsgrove UK
>
>
>
> Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
>
>
>
MPJG Sump Gasket
Posted: Fri Jan 25, 2002 12:43 am
by Roger Muir
Thanks for the replies regarding the use of silicone sealant.
I understand the problem with it becoming'stuck!'. I had the same problem
with the starter motor which I silicone sealed.
However the cork sump gaskets I think tend to be unnecessarily thick or too
soft. They do squeeze a great deal and you wonder how tight to take them
up.
The good thing about the MPJG block is that it is more or less one piece
apart from the main bearing holders which by their nature have to be tight.
The sump then becomes an integral part of the block once tightened. Also
modern silicone sealants ahve good 'flex' properties.
There I've just talked myself into using silicone!!
Regards to all......
Roger Muir Bromsgrove UK
Re: MPJG Sump Gasket
Posted: Fri Jan 25, 2002 5:36 am
by joecurto@aol.com
SILICONE UGH, one of the main problems with using silicone sealer in critical gasket areas is that you get "squiggles" of silicone on the inside where you can not remove, they usually wind up in the oil pump or the oil galleries causing the dreaded expensive sounds of "NO OIL PRESSURE", I like Permatex "High Tach" it comes in either a brush on or spray can, works well and no "squiggles"
Joe
Re: MPJG Sump Gasket
Posted: Fri Jan 25, 2002 6:15 am
by Mark McCombs
Joe and All- My other mechanical vice is vintage motorcycles. Recently, I was looking for a replacement sump plug for my Norton. Its a complex affair, a 1" outside thread with an inner cup with a filter screen- It look like a shot glass with threads on the outside. The screen is held in by a snap ring and the whole affair is allegedly the oil filter for the whole bike. Anyhow, I found 2 good used ones. As I disassembled them, I found the same things in each: Orange chunks of silcone and expensive pieces of ex-engine shards. I guess that how "just the filter plugs" came to be sold by themselves. Regards Mark TC8126
----- Original Message ----- [b]From:[/b]
joecurto@aol.com [b]To:[/b]
djensen@accessus.net ;
mg-tabc@yahoogroups.com [b]Sent:[/b] Friday, January 25, 2002 8:36 AM [b]Subject:[/b] Re: [mg-tabc] MPJG Sump Gasket
SILICONE UGH, one of the main problems with using silicone sealer in critical gasket areas is that you get "squiggles" of silicone on the inside where you can not remove, they usually wind up in the oil pump or the oil galleries causing the dreaded expensive sounds of "NO OIL PRESSURE", I like Permatex "High Tach" it comes in either a brush on or spray can, works well and no "squiggles"
Joe
Your use of Yahoo! Groups is subject to the
Yahoo! Terms of Service.
Re: MPJG Sump Gasket
Posted: Fri Jan 25, 2002 2:56 pm
by joecurto@aol.com
Mark I am sure that you did not pay the fellow anywhere near what it cost him for those plugs.
Joe