Page 1 of 1
turn signals don't work
Posted: Wed May 04, 2016 5:05 pm
by fciomaha
. The indicator light on the console does not light up and none of the Turn signal lights light up. I checked one of the bulbs last night and it was OK. Did not have time to check the rest yet. Have had the bike for 2 years but have not ridden it in the city till now. Also the neutral light does not come on either.. However the high beam light does. Any suggestions on where to start? Jeff told me to check the connections at the plugins in front and they seem ok.
turn signals don't work
Posted: Wed May 04, 2016 9:16 pm
by Steve Knott
Volt meter and clymer manual has full electrical print at the rear of the book.
Sent from my iPhone
On May 4, 2016, at 7:43 AM, fciomaha@... [DSN_KLR650] DSN_KLR650@yahoogroups.com> wrote:
. The indicator light on the console does not light up and none of the Turn signal lights light up. I checked one of the bulbs last night and it was OK. Did not have time to check the rest yet. Have had the bike for 2 years but have not ridden it in the city till now. Also the neutral light does not come on either.. However the high beam light does. Any suggestions on where to start? Jeff told me to check the connections at the plugins in front and they seem ok.
turn signals don't work
Posted: Thu May 05, 2016 11:02 pm
by Norm Keller
#ygrps-yiv-1167398199 blockquote.ygrps-yiv-1167398199cite {margin-left:5px;margin-right:0px;padding-left:10px;padding-right:0px;border-left:1px solid #cccccc;} #ygrps-yiv-1167398199 blockquote.ygrps-yiv-1167398199cite2 {margin-left:5px;margin-right:0px;padding-left:10px;padding-right:0px;border-left:1px solid #cccccc;margin-top:3px;padding-top:0px;} #ygrps-yiv-1167398199 .ygrps-yiv-1167398199plain pre, #ygrps-yiv-1167398199 .ygrps-yiv-1167398199plain tt {font-family:monospace;font-size:100%;font-weight:normal;font-style:normal;} #ygrps-yiv-1167398199 a img {border:0px;}#ygrps-yiv-1167398199 {font-family:Tahoma;font-size:12pt;} #ygrps-yiv-1167398199 .ygrps-yiv-1167398199plain pre, #ygrps-yiv-1167398199 .ygrps-yiv-1167398199plain tt {font-family:Tahoma;font-size:12pt;} Gen1 or Gen2?
The signals are powered from the Main Fuse so can't be that. The power comes off the Brown Wire after the ignition switch but if Brake Lights work, can't be that.
I can advise in more detail once know which generation.
Here is some detailed information on Gen1 wiring with plug and pin-outs, Junction locations and the whole 40 yards:
https://www.dropbox.com/sh/uha92pqkxq4eoaw/AABwFh5AIevN4dlJeZUitdjsa?dl=0
Here's Gen2:
https://www.dropbox.com/sh/bv8nr1untxi2inn/AABiA0CPjv2uDb4Q-bzpHyLEa?dl=0
turn signals don't work
Posted: Fri May 06, 2016 8:15 am
by Richard Watkins
Norm,
It is a 1989 so I think it is gen 1.
Richard
blown engine in mexico/yuma
Posted: Sat May 07, 2016 6:42 am
by jim reinhart
I want to hear more of the mexico moto story. your writing style is great. I just spent a week in baja on a KLR and have always wanted to ride the Copper Canyon thanks
turn signals don't work
Posted: Sat May 07, 2016 10:46 pm
by Richard Watkins
The flasher is bad. Anyone know what else will work? NAPA or Orielly's part #. 89 KLR 650.
turn signals don't work
Posted: Sat May 07, 2016 11:38 pm
by GMac999
Google an electronic flasher. I can t remember if it 2 or 3 terminal, but I think 2. With the electronic flasher, you can mix and match LED bulbs without affecting your turn signal rate. I picked mine up through Amazon for about $8. I m sure you could probably find them cheaper, possibly banggood.com or some other place. It s now a steady state no matter what the bulbs or RPMs. GregM [b]From:[/b]
DSN_KLR650@yahoogroups.com [mailto:
DSN_KLR650@yahoogroups.com]
[b]Sent:[/b] Saturday, May 07, 2016 3:32 PM
[b]To:[/b]
DSN_KLR650@yahoogroups.com
[b]Subject:[/b] [DSN_KLR650] Re: turn signals don't work
The flasher is bad. Anyone know what else will work? NAPA or Orielly's part #. 89 KLR 650.