blown engine in mexico/yuma

[fciomaha]

. The indicator light on the console does not light up and none of the Turn signal lights light up. I checked one of the bulbs last night and it was OK. Did not have time to check the rest yet. Have had the bike for 2 years but have not ridden it in the city till now. Also the neutral light does not come on either.. However the high beam light does. Any suggestions on where to start? Jeff told me to check the connections at the plugins in front and they seem ok.

[Steve Knott]

Volt meter and clymer manual has full electrical print at the rear of the book.  Sent from my iPhone

On May 4, 2016, at 7:43 AM, fciomaha@... [DSN_KLR650] DSN_KLR650@yahoogroups.com> wrote:

  . The indicator light on the console does not light up and none of the Turn signal lights light up. I checked one of the bulbs last night and it was OK. Did not have time to check the rest yet. Have had the bike for 2 years but have not ridden it in the city till now. Also the neutral light does not come on either.. However the high beam light does. Any suggestions on where to start? Jeff told me to check the connections at the plugins in front and they seem ok.

[Norm Keller]

#ygrps-yiv-1167398199 blockquote.ygrps-yiv-1167398199cite {margin-left:5px;margin-right:0px;padding-left:10px;padding-right:0px;border-left:1px solid #cccccc;} #ygrps-yiv-1167398199 blockquote.ygrps-yiv-1167398199cite2 {margin-left:5px;margin-right:0px;padding-left:10px;padding-right:0px;border-left:1px solid #cccccc;margin-top:3px;padding-top:0px;} #ygrps-yiv-1167398199 .ygrps-yiv-1167398199plain pre, #ygrps-yiv-1167398199 .ygrps-yiv-1167398199plain tt {font-family:monospace;font-size:100%;font-weight:normal;font-style:normal;} #ygrps-yiv-1167398199 a img {border:0px;}#ygrps-yiv-1167398199 {font-family:Tahoma;font-size:12pt;} #ygrps-yiv-1167398199 .ygrps-yiv-1167398199plain pre, #ygrps-yiv-1167398199 .ygrps-yiv-1167398199plain tt {font-family:Tahoma;font-size:12pt;} Gen1 or Gen2? The signals are powered from the Main Fuse so can't be that. The power comes off the Brown Wire after the ignition switch but if Brake Lights work, can't be that. I can advise in more detail once know which generation. Here is some detailed information on Gen1 wiring with plug and pin-outs, Junction locations and the whole 40 yards: https://www.dropbox.com/sh/uha92pqkxq4eoaw/AABwFh5AIevN4dlJeZUitdjsa?dl=0 Here's Gen2: https://www.dropbox.com/sh/bv8nr1untxi2inn/AABiA0CPjv2uDb4Q-bzpHyLEa?dl=0

[Richard Watkins]

Norm,

It is a 1989 so I think it is gen 1.

Richard

[jim reinhart]

I want to hear more of the mexico moto story. your writing style is great. I just spent a week in baja on a KLR and have always wanted to ride the Copper Canyon thanks

[Richard Watkins]

The flasher is bad. Anyone know what else will work? NAPA or Orielly's part #. 89 KLR 650.

[GMac999]

Google an electronic flasher. I can t remember if it 2 or 3 terminal, but I think 2.

 

With the electronic flasher, you can mix and match LED bulbs without affecting your turn signal rate. I picked mine up through Amazon for about $8. I m sure you could probably find them cheaper, possibly banggood.com or some other place.

 

It s now a steady state no matter what the bulbs or RPMs.

 

GregM

 

 

[b]From:[/b] DSN_KLR650@yahoogroups.com [mailto:DSN_KLR650@yahoogroups.com] [b]Sent:[/b] Saturday, May 07, 2016 3:32 PM [b]To:[/b] DSN_KLR650@yahoogroups.com [b]Subject:[/b] [DSN_KLR650] Re: turn signals don't work

 

The flasher is bad. Anyone know what else will work? NAPA or Orielly's part #. 89 KLR 650.