Page 1 of 1

motorcycle scissor jack

Posted: Mon Aug 05, 2013 7:54 pm
by Ian Francisco
Stumbled across this scissor jack while browsing and thought I would share it with my Yahoo groups. For $70 it seems reasonable, and for that price you could get two of them. http://www.discountramps.com/motorcycle-lift-jack.htm?CA_6C15C=774981029 -- *Ian Francisco http://www.scarletfuries.com http://www.facebook.com/pages/The-Scarlet-Furies/121218125931* [Non-text portions of this message have been removed]

motorcycle scissor jack

Posted: Tue Aug 06, 2013 6:48 am
by Michael Burwell
Yes, but that's a pretty bad name from a marketing standpoint; I thought "Widowmaker" when I read it. Michael Sent from my iPad

motorcycle scissor jack

Posted: Tue Aug 06, 2013 10:29 am
by Jeff Khoury
And why, oh why... does there have to be some douche-y cruiser in all the pics? -Jeff Khoury
----- Original Message ----- From: "Michael Burwell" To: "DSN KLR650" DSN_KLR650@yahoogroups.com> Sent: Tuesday, August 6, 2013 4:48:45 AM Subject: [DSN_KLR650] Re: motorcycle scissor jack Yes, but that's a pretty bad name from a marketing standpoint; I thought "Widowmaker" when I read it. Michael Sent from my iPad

motorcycle scissor jack

Posted: Tue Aug 06, 2013 11:51 am
by mark ward
or fear it will tip over. You always put SCRAP in the test item. (shhhh. ok I also love my cruisers, But my KLR is #1.)
>________________________________ > From: Jeff Khoury >To: Michael Burwell >Cc: DSN KLR650 DSN_KLR650@yahoogroups.com> >Sent: Tuesday, August 6, 2013 11:29 AM >Subject: Re: [DSN_KLR650] Re: motorcycle scissor jack > > > >And why, oh why... does there have to be some douche-y cruiser in all the pics? > >-Jeff Khoury > >----- Original Message ----- >From: "Michael Burwell" >To: "DSN KLR650" >Sent: Tuesday, August 6, 2013 4:48:45 AM >Subject: [DSN_KLR650] Re: motorcycle scissor jack > >Yes, but that's a pretty bad name from a marketing standpoint; I thought "Widowmaker" when I read it. >Michael > >Sent from my iPad > > >
[Non-text portions of this message have been removed]

just started backfiring and stalling.

Posted: Tue Aug 06, 2013 3:04 pm
by achesley43@ymail.com
Another thing to check while your in there is the Plug Cap. Take it apart , cut a little of the main wire off , clean it , put it back together with Dielectric Grease. I had a but of what I thought was a carb problem a few years back, took it all apart and same thing when getting it back together. Plug Cap was the culprit. So may as well do that while your apart cleaning the carb.
--- In DSN_KLR650@yahoogroups.com, brucebordt@... wrote: > > I've got a 2000 (A14) with 20500 miles on it. I drove it two weeks ago and all was fine. Jumped on it today and with the choke completely off, the engine would back fire on release of the throttle and eventually stall when attempting to idle. If I gave it just a little choke all was well again; it drove like normal. > > Anyone else had this problem? Any ideas what is likely the problem? The carb has never been touched. Plug was changed twice and valve clearances adjusted as needed. Everything else on it is factory stock except for doo-hickey replacement many years ago. > > Thanks, > > Bruce >

motorcycle scissor jack

Posted: Tue Aug 06, 2013 3:16 pm
by achesley43@ymail.com
Been using one of them old scissor jacks for years. But, use it just on my lift and it's about 1/2 the size of that one. Then I have the bike strapped down with the front in the chock. Nice to work on suspension where you can adjust the level of the bike. Hmmmmmm Let's see, Have used it on Harleys, Triumphs, Suzukis, Yamahas, Hondas, Vespa's, BMW's and even on my Kawasaki's. LOL!
--- In DSN_KLR650@yahoogroups.com, Ian Francisco wrote: > > Stumbled across this scissor jack while browsing and thought I would share > it with my Yahoo groups. For $70 it seems reasonable, and for that price > you could get two of them. > > http://www.discountramps.com/motorcycle-lift-jack.htm?CA_6C15C=774981029 > -- > *Ian Francisco > http://www.scarletfuries.com > http://www.facebook.com/pages/The-Scarlet-Furies/121218125931* > > > [Non-text portions of this message have been removed] >