Page 1 of 1
dual star centerstand installation question
Posted: Thu Mar 29, 2007 7:41 am
by BobR
I just purchased a Dual Star centerstand off e-bay. I had read that it is a
simple bolt on but when I started to install it on my 06 it didn't seem
quite wide enough to mount where the pegs are. Is there some installation
trick that I'm missing?
After reading all the posts for/against centerstands I was on the fence and
was only planning to install it for use on a long trip with minimal gravel
roads. If I have to grind something or modify something I'm not as
interested in using it.
Great forum but the way, very active and credible.
Bob
[Non-text portions of this message have been removed]
dual star centerstand installation question
Posted: Thu Mar 29, 2007 8:39 am
by Jeff Saline
On Thu, 29 Mar 2007 06:31:33 -0400 "BobR"
writes:
> I just purchased a Dual Star centerstand off e-bay. I had read that
> it is a
> simple bolt on but when I started to install it on my 06 it didn't
> seem
> quite wide enough to mount where the pegs are. Is there some
> installation
> trick that I'm missing?
>
>
>
> After reading all the posts for/against centerstands I was on the
> fence and
> was only planning to install it for use on a long trip with minimal
> gravel
> roads. If I have to grind something or modify something I'm not as
> interested in using it.
>
>
>
> Great forum but the way, very active and credible.
<><><><><><><><>
<><><><><><><><>
Bob,
I've installed a few centerstands and all have been tight fits. I've
used a large hammer to beat them into place over the footpeg mounts. If
you are going to do stuff to your rear suspension linkage like lube
needle bearings you need to remove the centerstand and loosen the engine
rear mount bolt. Otherwise the frame will be too tight and if you get
the suspension part out you won't get it back in.
Make sure you are careful with your torque of the footpeg bolts. I seem
to recall it's 18 foot pounds but haven't messed with mine in two years.
I did have one strip the threads and replaced the four footpeg bolts with
M10 bolts.
The forum is way to active lately. : ) We're probably gonna read this 6
times in the next week. : )
Best,
Jeff Saline
ABC # 4412 South Dakota Airmarshal
Airheads Beemer Club
www.airheads.org
The Beautiful Black Hills of South Dakota
75 R90/6, 03 KLR650, 79 R100RT
dual star centerstand installation question
Posted: Thu Mar 29, 2007 10:10 am
by kestrelfal
Centerstands with a fixed-dimension between
the mounting plates do not allow for frame
dimensional changes by mfr'r, or tolerances.
Not a good design feature. If the mounting
plates are not sandwiched perfectly flat
between the footrest and frame brackets, the
bolted joints may loosen and fail. The SW-MOTECH
centerstand has floating mounting plates and
avoids the fixed-dimension design flaw.
Fred
--- In
DSN_KLR650@yahoogroups.com, "BobR" wrote:
>
> I just purchased a Dual Star centerstand off e-bay. I had read that
it is a
> simple bolt on but when I started to install it on my 06 it didn't seem
> quite wide enough to mount where the pegs are. Is there some
installation
> trick that I'm missing?
>
>
>
> After reading all the posts for/against centerstands I was on the
fence and
> was only planning to install it for use on a long trip with minimal
gravel
> roads. If I have to grind something or modify something I'm not as
> interested in using it.
>
>
>
> Great forum but the way, very active and credible.
>
>
>
> Bob
>
>
>
> [Non-text portions of this message have been removed]
>
dual star centerstand installation question
Posted: Thu Mar 29, 2007 5:03 pm
by bobrehley@carolina.rr.com
Thanks Jeff. I think a hammer just might work, it's so close to
fitting. I'll also put some shims under the sidestand (or have my wife
hold it) to keep the bike more upright when I do it. It was leaned
over on the stand when I tried last night and I'm sure the side
pressure didn't help much.
Bob
----- Original Message -----
From: Jeff Saline
Date: Thursday, March 29, 2007 9:40 am
Subject: Re: [DSN_KLR650] Dual Star Centerstand Installation Question
To: bobrehley@...
Cc:
DSN_KLR650@yahoogroups.com
> On Thu, 29 Mar 2007 06:31:33 -0400 "BobR"
> writes:
> > I just purchased a Dual Star centerstand off e-bay. I had read
> that
> > it is a
> > simple bolt on but when I started to install it on my 06 it
> didn't
> > seem
> > quite wide enough to mount where the pegs are. Is there some
> > installation
> > trick that I'm missing?
> >
> >
> >
> > After reading all the posts for/against centerstands I was on
> the
> > fence and
> > was only planning to install it for use on a long trip with
> minimal
> > gravel
> > roads. If I have to grind something or modify something I'm not as
> > interested in using it.
> >
> >
> >
> > Great forum but the way, very active and credible.
> <><><><><><><><>
> <><><><><><><><>
>
> Bob,
>
> I've installed a few centerstands and all have been tight fits. I've
> used a large hammer to beat them into place over the footpeg
> mounts. If
> you are going to do stuff to your rear suspension linkage like lube
> needle bearings you need to remove the centerstand and loosen the
> enginerear mount bolt. Otherwise the frame will be too tight and
> if you get
> the suspension part out you won't get it back in.
>
> Make sure you are careful with your torque of the footpeg bolts.
> I seem
> to recall it's 18 foot pounds but haven't messed with mine in two
> years.
> I did have one strip the threads and replaced the four footpeg
> bolts with
> M10 bolts.
>
> The forum is way to active lately. : ) We're probably gonna read
> this 6
> times in the next week. : )
>
> Best,
>
> Jeff Saline
> ABC # 4412 South Dakota Airmarshal
> Airheads Beemer Club
www.airheads.org
> The Beautiful Black Hills of South Dakota
> 75 R90/6, 03 KLR650, 79 R100RT
>
got bags!! however i am worried about exhaust.
Posted: Fri Mar 30, 2007 10:15 am
by CA Stu
--- In
DSN_KLR650@yahoogroups.com, "probertucci"
wrote:
>
> Hey guys,
>
>
> Got a new set of soft bags (FirstGears). They look great but I am
> worried about heat from the pipe. I could move the bags forward
but it
> kinds looks funny. Suggestions???
>
> Thanks
>
> Pete
>
You need to make sure they are far enough away from the muffler to
stay cool.
Despite what you may think, it's not much fun getting off the highway
in Barstow to find that your socks and underwear are smoking,
smoldering and about to burst into flames.
Thanks
CA Stu