Re: V2 Neon backplate [1 Attachment]

[dhuber0262]

Sorry Ken, This email though me off.

David

---- "acropolisuniversity@gmail.com [B9Builders]" wrote:

> Awesome job, David! It looks great! Sent you an e-mail.

[David Schulpius]

This thrilling new B9 part is now listed on Dave Huber's vendor page over on our B9 Builders website. Thanks for the help Tex on getting this update on Dave's page!
Please head over there for a look. You may need to refresh your browser to see it. http://www.b9robotbuildersclub.com/pub/parts/B90262/index.html Thanks and have fun.
Dave Schulpius

On Nov 16, 2015 8:36 PM, "dandbhuber@twc.com [B9Builders]" wrote:
[Attachment(s) from dandbhuber@twc.com included below]
Guys,

I have been working with Craig R for a few months on a backplate for
the V2 Torso and it's finally ready. The V2 backplate is a work of
art and it fits the V2 Torso like a glove. Craig might want to chime
in on this but he thinks this back plate has origins that go all the
way back to the hero backplate. He has worked months and months
correcting the flaws that were in the hero backplate to bring this
backplate up to his standards. I worked with him on the final design
and I produce them in my state of the art backplate manufacturing
facility(my kitchen). I just finished a run and they are ready for immediate shipping.

As an added bonus the V2 backplate is .100 thick, while my old
backplates were .080. that might not sound like much but believe me, it is!

The V2 backplate has been verified to fit the V2 Torso but it should
fit any torso.

I've attached some pictures of the new V2 backplate

It turns out there is a bit of a learning curve forming thicker
styrene. I have two backplates that had a small wrinkle in the
bottom where it attaches behind the large chest lights. I have
sanded the flaw out and once installed it can't be seen but I'll let
these go for $50 each + shipping a $15 dollar savings. Please e-mail
me privately if interested.

David H

[dhuber0262]

Attachments :

1. [url=file:///C:\Users\CyberPigStudio\AppData\Local\PG Offline 4\Attachments\B9Builders\backplate1-51514.jpg]backplate1-51514.jpg[/url]

Guys,

Just so there's no confusion, the backplate pictured on my vendor page is not the new V2 back plate. That picture is the backplate I make for use with the neon Dennis W used to sell. Please see the attached picture for the V2 backplate. Thanks!

David

---- "David Schulpius dschulpius@gmail.com [B9Builders]" wrote:

> This thrilling new B9 part is now listed on Dave Huber's vendor page over
> on our B9 Builders website. Thanks for the help Tex on getting this update
> on Dave's page!
> Please head over there for a look. You may need to refresh your browser to
> see it.
>
> http://www.b9robotbuildersclub.com/pub/parts/B90262/index.html
>
> Thanks and have fun.
> Dave Schulpius
> On Nov 16, 2015 8:36 PM, "dandbhuber@twc.com [B9Builders]" <
> B9Builders@yahoogroups.com> wrote:
>
> >
> > [Attachment(s) from dandbhuber@twc.com
> > included below]
> >
> > Guys,
> >
> > I have been working with Craig R for a few months on a backplate for
> > the V2 Torso and it's finally ready. The V2 backplate is a work of
> > art and it fits the V2 Torso like a glove. Craig might want to chime
> > in on this but he thinks this back plate has origins that go all the
> > way back to the hero backplate. He has worked months and months
> > correcting the flaws that were in the hero backplate to bring this
> > backplate up to his standards. I worked with him on the final design
> > and I produce them in my state of the art backplate manufacturing
> > facility(my kitchen). I just finished a run and they are ready for
> > immediate shipping.
> >
> > As an added bonus the V2 backplate is .100 thick, while my old
> > backplates were .080. that might not sound like much but believe me, it
> > is!
> >
> > The V2 backplate has been verified to fit the V2 Torso but it should
> > fit any torso.
> >
> > I've attached some pictures of the new V2 backplate
> >
> > It turns out there is a bit of a learning curve forming thicker
> > styrene. I have two backplates that had a small wrinkle in the
> > bottom where it attaches behind the large chest lights. I have
> > sanded the flaw out and once installed it can't be seen but I'll let
> > these go for $50 each + shipping a $15 dollar savings. Please e-mail
> > me privately if interested.
> >
> > David H
> >
> >

[David Schulpius]

Yes, sorry Dave. I don't know how I got that pic screwed up. I'll get it fixed asap.
Dave Schulpius

On Wed, Nov 18, 2015 at 5:24 PM, dandbhuber@twc.com [B9Builders] wrote:
[Attachment(s) from dandbhuber@twc.com included below]
Guys,

Just so there's no confusion, the backplate pictured on my vendor page is not the new V2 back plate. That picture is the backplate I make for use with the neon Dennis W used to sell. Please see the attached picture for the V2 backplate. Thanks!

David

---- "David Schulpius dschulpius@gmail.com [B9Builders]" wrote:
> This thrilling new B9 part is now listed on Dave Huber's vendor page over
> on our B9 Builders website. Thanks for the help Tex on getting this update
> on Dave's page!
> Please head over there for a look. You may need to refresh your browser to
> see it.
>
> http://www.b9robotbuildersclub.com/pub/parts/B90262/index.html
>
> Thanks and have fun.
> Dave Schulpius
> On Nov 16, 2015 8:36 PM, "dandbhuber@twc.com [B9Builders]" <
> B9Builders@yahoogroups.com> wrote:
>
> >
> > [Attachment(s) from dandbhuber@twc.com
> > included below]
> >
> > Guys,
> >
> > I have been working with Craig R for a few months on a backplate for
> > the V2 Torso and it's finally ready. The V2 backplate is a work of
> > art and it fits the V2 Torso like a glove. Craig might want to chime
> > in on this but he thinks this back plate has origins that go all the
> > way back to the hero backplate. He has worked months and months
> > correcting the flaws that were in the hero backplate to bring this
> > backplate up to his standards. I worked with him on the final design
> > and I produce them in my state of the art backplate manufacturing
> > facility(my kitchen). I just finished a run and they are ready for
> > immediate shipping.
> >
> > As an added bonus the V2 backplate is .100 thick, while my old
> > backplates were .080. that might not sound like much but believe me, it
> > is!
> >
> > The V2 backplate has been verified to fit the V2 Torso but it should
> > fit any torso.
> >
> > I've attached some pictures of the new V2 backplate
> >
> > It turns out there is a bit of a learning curve forming thicker
> > styrene. I have two backplates that had a small wrinkle in the
> > bottom where it attaches behind the large chest lights. I have
> > sanded the flaw out and once installed it can't be seen but I'll let
> > these go for $50 each + shipping a $15 dollar savings. Please e-mail
> > me privately if interested.
> >
> > David H
> >
> >

[dhuber0262]

No Problem Dave. I knew it was just one of those things. Thanks!


---- "David Schulpius dschulpius@wi.rr.com [B9Builders]" wrote:

> Yes, sorry Dave. I don't know how I got that pic screwed up. I'll get it
> fixed asap.
>
> Dave Schulpius
>
> On Wed, Nov 18, 2015 at 5:24 PM, dandbhuber@twc.com [B9Builders] <
> B9Builders@yahoogroups.com> wrote:
>
> >
> > [Attachment(s) from dandbhuber@twc.com
> > included below]
> >
> > Guys,
> >
> > Just so there's no confusion, the backplate pictured on my vendor page is
> > not the new V2 back plate. That picture is the backplate I make for use
> > with the neon Dennis W used to sell. Please see the attached picture for
> > the V2 backplate. Thanks!
> >
> > David
> >
> > ---- "David Schulpius dschulpius@gmail.com [B9Builders]" <
> > B9Builders@yahoogroups.com> wrote:
> > > This thrilling new B9 part is now listed on Dave Huber's vendor page over
> > > on our B9 Builders website. Thanks for the help Tex on getting this
> > update
> > > on Dave's page!
> > > Please head over there for a look. You may need to refresh your browser
> > to
> > > see it.
> > >
> > > http://www.b9robotbuildersclub.com/pub/parts/B90262/index.html
> > >
> > > Thanks and have fun.
> > > Dave Schulpius
> > > On Nov 16, 2015 8:36 PM, "dandbhuber@twc.com [B9Builders]" <
> > > B9Builders@yahoogroups.com> wrote:
> > >
> > > >
> > > > [Attachment(s) from dandbhuber@twc.com
> > > > included below]
> > > >
> > > > Guys,
> > > >
> > > > I have been working with Craig R for a few months on a backplate for
> > > > the V2 Torso and it's finally ready. The V2 backplate is a work of
> > > > art and it fits the V2 Torso like a glove. Craig might want to chime
> > > > in on this but he thinks this back plate has origins that go all the
> > > > way back to the hero backplate. He has worked months and months
> > > > correcting the flaws that were in the hero backplate to bring this
> > > > backplate up to his standards. I worked with him on the final design
> > > > and I produce them in my state of the art backplate manufacturing
> > > > facility(my kitchen). I just finished a run and they are ready for
> > > > immediate shipping.
> > > >
> > > > As an added bonus the V2 backplate is .100 thick, while my old
> > > > backplates were .080. that might not sound like much but believe me, it
> > > > is!
> > > >
> > > > The V2 backplate has been verified to fit the V2 Torso but it should
> > > > fit any torso.
> > > >
> > > > I've attached some pictures of the new V2 backplate
> > > >
> > > > It turns out there is a bit of a learning curve forming thicker
> > > > styrene. I have two backplates that had a small wrinkle in the
> > > > bottom where it attaches behind the large chest lights. I have
> > > > sanded the flaw out and once installed it can't be seen but I'll let
> > > > these go for $50 each + shipping a $15 dollar savings. Please e-mail
> > > > me privately if interested.
> > > >
> > > > David H
> > > >
> > > >
> >
> >

[Jeff DeRose]

Oh man!  Now my everyday ordinary backplate looks so sad with its one little picture....!  Speaking of, I've mounted it in my barton torso with Craig's neon and it fits amazingly well!  Very little gaps.
Jeff-

Sent from my iPad

On Nov 18, 2015, at 6:37 PM, "dandbhuber@twc.com [B9Builders]" wrote:

 
No Problem Dave. I knew it was just one of those things. Thanks!

---- "David Schulpius dschulpius@wi.rr.com [B9Builders]" wrote:
> Yes, sorry Dave. I don't know how I got that pic screwed up. I'll get it
> fixed asap.
>
> Dave Schulpius
>
> On Wed, Nov 18, 2015 at 5:24 PM, dandbhuber@twc.com [B9Builders] <
> B9Builders@yahoogroups.com> wrote:
>
> >
> > [Attachment(s) from dandbhuber@twc.com
> > included below]
> >
> > Guys,
> >
> > Just so there's no confusion, the backplate pictured on my vendor page is
> > not the new V2 back plate. That picture is the backplate I make for use
> > with the neon Dennis W used to sell. Please see the attached picture for
> > the V2 backplate. Thanks!
> >
> > David
> >
> > ---- "David Schulpius dschulpius@gmail.com [B9Builders]" <
> > B9Builders@yahoogroups.com> wrote:
> > > This thrilling new B9 part is now listed on Dave Huber's vendor page over
> > > on our B9 Builders website. Thanks for the help Tex on getting this
> > update
> > > on Dave's page!
> > > Please head over there for a look. You may need to refresh your browser
> > to
> > > see it.
> > >
> > > http://www.b9robotbuildersclub.com/pub/parts/B90262/index.html
> > >
> > > Thanks and have fun.
> > > Dave Schulpius
> > > On Nov 16, 2015 8:36 PM, "dandbhuber@twc.com [B9Builders]" <
> > > B9Builders@yahoogroups.com> wrote:
> > >
> > > >
> > > > [Attachment(s) from dandbhuber@twc.com
> > > > included below]
> > > >
> > > > Guys,
> > > >
> > > > I have been working with Craig R for a few months on a backplate for
> > > > the V2 Torso and it's finally ready. The V2 backplate is a work of
> > > > art and it fits the V2 Torso like a glove. Craig might want to chime
> > > > in on this but he thinks this back plate has origins that go all the
> > > > way back to the hero backplate. He has worked months and months
> > > > correcting the flaws that were in the hero backplate to bring this
> > > > backplate up to his standards. I worked with him on the final design
> > > > and I produce them in my state of the art backplate manufacturing
> > > > facility(my kitchen). I just finished a run and they are ready for
> > > > immediate shipping.
> > > >
> > > > As an added bonus the V2 backplate is .100 thick, while my old
> > > > backplates were .080. that might not sound like much but believe me, it
> > > > is!
> > > >
> > > > The V2 backplate has been verified to fit the V2 Torso but it should
> > > > fit any torso.
> > > >
> > > > I've attached some pictures of the new V2 backplate
> > > >
> > > > It turns out there is a bit of a learning curve forming thicker
> > > > styrene. I have two backplates that had a small wrinkle in the
> > > > bottom where it attaches behind the large chest lights. I have
> > > > sanded the flaw out and once installed it can't be seen but I'll let
> > > > these go for $50 each + shipping a $15 dollar savings. Please e-mail
> > > > me privately if interested.
> > > >
> > > > David H
> > > >
> > > >
> >
> >

[Brian Gaiser]

Jeff just what I wanted to hear! 


=========================
Brian Gaiser
=========================

On Nov 19, 2015, at 00:11, Jeff DeRose jeff.derose@comcast.net [B9Builders] wrote:

Oh man!  Now my everyday ordinary backplate looks so sad with its one little picture....!  Speaking of, I've mounted it in my barton torso with Craig's neon and it fits amazingly well!  Very little gaps.
Jeff-

Sent from my iPad
On Nov 18, 2015, at 6:37 PM, "dandbhuber@twc.com [B9Builders]" wrote:

 No Problem Dave. I knew it was just one of those things. Thanks!

---- "David Schulpius dschulpius@wi.rr.com [B9Builders]" wrote: 
> Yes, sorry Dave. I don't know how I got that pic screwed up. I'll get it
> fixed asap.
> 
> Dave Schulpius
> 
> On Wed, Nov 18, 2015 at 5:24 PM, dandbhuber@twc.com [B9Builders] <
> B9Builders@yahoogroups.com> wrote:
> 
> >
> > [Attachment(s) from dandbhuber@twc.com
> > included below]
> >
> > Guys,
> >
> > Just so there's no confusion, the backplate pictured on my vendor page is
> > not the new V2 back plate. That picture is the backplate I make for use
> > with the neon Dennis W used to sell. Please see the attached picture for
> > the V2 backplate. Thanks!
> >
> > David
> >
> > ---- "David Schulpius dschulpius@gmail.com [B9Builders]" <
> > B9Builders@yahoogroups.com> wrote:
> > > This thrilling new B9 part is now listed on Dave Huber's vendor page over
> > > on our B9 Builders website. Thanks for the help Tex on getting this
> > update
> > > on Dave's page!
> > > Please head over there for a look. You may need to refresh your browser
> > to
> > > see it.
> > >
> > > http://www.b9robotbuildersclub.com/pub/parts/B90262/index.html
> > >
> > > Thanks and have fun.
> > > Dave Schulpius
> > > On Nov 16, 2015 8:36 PM, "dandbhuber@twc.com [B9Builders]" <
> > > B9Builders@yahoogroups.com> wrote:
> > >
> > > >
> > > > [Attachment(s) from dandbhuber@twc.com
> > > > included below]
> > > >
> > > > Guys,
> > > >
> > > > I have been working with Craig R for a few months on a backplate for
> > > > the V2 Torso and it's finally ready. The V2 backplate is a work of
> > > > art and it fits the V2 Torso like a glove. Craig might want to chime
> > > > in on this but he thinks this back plate has origins that go all the
> > > > way back to the hero backplate. He has worked months and months
> > > > correcting the flaws that were in the hero backplate to bring this
> > > > backplate up to his standards. I worked with him on the final design
> > > > and I produce them in my state of the art backplate manufacturing
> > > > facility(my kitchen). I just finished a run and they are ready for
> > > > immediate shipping.
> > > >
> > > > As an added bonus the V2 backplate is .100 thick, while my old
> > > > backplates were .080. that might not sound like much but believe me, it
> > > > is!
> > > >
> > > > The V2 backplate has been verified to fit the V2 Torso but it should
> > > > fit any torso.
> > > >
> > > > I've attached some pictures of the new V2 backplate
> > > >
> > > > It turns out there is a bit of a learning curve forming thicker
> > > > styrene. I have two backplates that had a small wrinkle in the
> > > > bottom where it attaches behind the large chest lights. I have
> > > > sanded the flaw out and once installed it can't be seen but I'll let
> > > > these go for $50 each + shipping a $15 dollar savings. Please e-mail
> > > > me privately if interested.
> > > >
> > > > David H
> > > >
> > > >
> > 
> >

[David Schulpius]

We're having coding issues with David Huber's vendor page. If you're using Chrome you may see some odd things till we get things worked out. If possable try viewing his page in Firefox or IE till we work through this. Thouse browsers seem to be displaying his page properly. Sorry for any inconvenience. Dave Schulpius

On Nov 18, 2015 8:37 PM, "dandbhuber@twc.com [B9Builders]" wrote:

No Problem Dave. I knew it was just one of those things. Thanks!

---- "David Schulpius dschulpius@wi.rr.com [B9Builders]" wrote:
> Yes, sorry Dave. I don't know how I got that pic screwed up. I'll get it
> fixed asap.
>
> Dave Schulpius
>
> On Wed, Nov 18, 2015 at 5:24 PM, dandbhuber@twc.com [B9Builders] <
> B9Builders@yahoogroups.com> wrote:
>
> >
> > [Attachment(s) from dandbhuber@twc.com
> > included below]
> >
> > Guys,
> >
> > Just so there's no confusion, the backplate pictured on my vendor page is
> > not the new V2 back plate. That picture is the backplate I make for use
> > with the neon Dennis W used to sell. Please see the attached picture for
> > the V2 backplate. Thanks!
> >
> > David
> >
> > ---- "David Schulpius dschulpius@gmail.com [B9Builders]" <
> > B9Builders@yahoogroups.com> wrote:
> > > This thrilling new B9 part is now listed on Dave Huber's vendor page over
> > > on our B9 Builders website. Thanks for the help Tex on getting this
> > update
> > > on Dave's page!
> > > Please head over there for a look. You may need to refresh your browser
> > to
> > > see it.
> > >
> > > http://www.b9robotbuildersclub.com/pub/parts/B90262/index.html
> > >
> > > Thanks and have fun.
> > > Dave Schulpius
> > > On Nov 16, 2015 8:36 PM, "dandbhuber@twc.com [B9Builders]" <
> > > B9Builders@yahoogroups.com> wrote:
> > >
> > > >
> > > > [Attachment(s) from dandbhuber@twc.com
> > > > included below]
> > > >
> > > > Guys,
> > > >
> > > > I have been working with Craig R for a few months on a backplate for
> > > > the V2 Torso and it's finally ready. The V2 backplate is a work of
> > > > art and it fits the V2 Torso like a glove. Craig might want to chime
> > > > in on this but he thinks this back plate has origins that go all the
> > > > way back to the hero backplate. He has worked months and months
> > > > correcting the flaws that were in the hero backplate to bring this
> > > > backplate up to his standards. I worked with him on the final design
> > > > and I produce them in my state of the art backplate manufacturing
> > > > facility(my kitchen). I just finished a run and they are ready for
> > > > immediate shipping.
> > > >
> > > > As an added bonus the V2 backplate is .100 thick, while my old
> > > > backplates were .080. that might not sound like much but believe me, it
> > > > is!
> > > >
> > > > The V2 backplate has been verified to fit the V2 Torso but it should
> > > > fit any torso.
> > > >
> > > > I've attached some pictures of the new V2 backplate
> > > >
> > > > It turns out there is a bit of a learning curve forming thicker
> > > > styrene. I have two backplates that had a small wrinkle in the
> > > > bottom where it attaches behind the large chest lights. I have
> > > > sanded the flaw out and once installed it can't be seen but I'll let
> > > > these go for $50 each + shipping a $15 dollar savings. Please e-mail
> > > > me privately if interested.
> > > >
> > > > David H
> > > >
> > > >
> >
> >

[monstermodelman1]

I just received the very first #001 v2 neon backplate from David Huber and I can tell you we are truly blessed to have such talented people producing high quality parts for our B9. This is a work of art and fits beautifully in Craig's v2 torso. Buy it now as you won't be dissappointed. Once I get my neon and can get this painted and trimmed (only a very little) around the top ring hole...and then mounted, I will post pictures for all to see.

Thanks David for such a much needed part and the quality workmanship!!

Bob Jaconetti
B9-0663

[dhuber0262]

Thanks Bob! I'm glad you like it.

David H

---- "bobjacon@gmail.com [B9Builders]" wrote:

> I just received the very first #001 v2 neon backplate from David Huber and I can tell you we are truly blessed to have such talented people producing high quality parts for our B9. This is a work of art and fits beautifully in Craig's v2 torso. Buy it now as you won't be dissappointed. Once I get my neon and can get this painted and trimmed (only a very little) around the top ring hole...and then mounted, I will post pictures for all to see.

Thanks David for such a much needed part and the quality workmanship!!

Bob Jaconetti
B9-0663